Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
newtom_go_floor_site_prep [2019/08/22 13:13]
admin
newtom_go_floor_site_prep [2019/08/22 13:15] (current)
admin
Line 1: Line 1:
 +
 === NewTom GO Floor-Mount === === NewTom GO Floor-Mount ===
 ---- ----
-<alert info>​PHYSICAL ROOM REQUIREMENTS </alert>+<code>​PHYSICAL ROOM REQUIREMENTS </code> 
 +The NewTom GO requires a minimum physical space of 45.9" wide, 64.5" deep, and 88.8" tall. The requirements for width and depth take into account the space needed for the patient to walk around the device and for the operator to use the device.  
 +<​bootnote warning>​24"​clearance on right side of machine is compulsory. Failure to meet this requirement will result in ergonomic and operational issues for clinic staff.</​bootnote>
  
-==Physical Room Requirements== 
- 
- 
-The NewTom GO require a minimum physical space of 45.9" wide, 64.5" deep, and 88.8" tall. The requirements for width and depth take into account the space needed for the patient to walk around the device and for the operator to use the device. ​ 
- 
-<​bootnote critical>​Follow all local, state, and federal rules relating to ADA accessibility,​ code enforcement,​ and fire code. </​bootnote>​ 
- 
-<​bootnote warning>​24"​clearance on right side of machine is compulsory. Failure to meet this requirement will result in ergonomic and operational issues for clinic staff.</​bootnote>​ 
 {{:​wiki:​476px-go-x5_top_down.png?​225|}} {{:​wiki:​476px-go-x5_top_down.png?​225|}}
 {{:​wiki:​go_x5_floor_front.png?​225|}} {{:​wiki:​go_x5_floor_front.png?​225|}}
 {{:​wiki:​go_x5_floor_side.png?​225|}} {{:​wiki:​go_x5_floor_side.png?​225|}}
- 
 ---- ----
- +<code>​MOUNTING OPTIONS</​code>
-<alert info>​MOUNTING OPTIONS</​alert>+
 {{ :​wiki:​600px-go_x5_plates_brackets.png?​nolink |}} {{ :​wiki:​600px-go_x5_plates_brackets.png?​nolink |}}
- +\\ \\
-**Brackets and Plates**+
   - Free-standing base kit for use with floor column (Floor-mount only)   - Free-standing base kit for use with floor column (Floor-mount only)
   - 16” on-center mounting plate with threaded rod - Can be used on it’s own if wood studs 16” on-center exist. (Wall-mount only)   - 16” on-center mounting plate with threaded rod - Can be used on it’s own if wood studs 16” on-center exist. (Wall-mount only)
Line 32: Line 24:
 ---- ----
  
-<alert info>​ELECTRICAL REQUIREMENTS </alert+<code>​ELECTRICAL REQUIREMENTS </code
-The NewTom GO requires a dedicated 20A breaker with NEMA L520-compliant receptacle and plug. The NEMA L520 receptacle, plug, and supply cable are provided with each unit. Wiring between the outlet and the electrical panel should be rated for 20A. Surge protection is highly-recommended and not provided as part of the equipment accessories. ​+The NewTom GO requires a dedicated ​115V 20A breaker with NEMA L520-compliant receptacle and plug. The NEMA L520 receptacle, plug, and supply cable are provided with each unit. Wiring between the outlet and the electrical panel should be rated for 20A. Surge protection is highly-recommended and not provided as part of the equipment accessories. ​
 {{ :​wiki:​200px-nema_l520.png?​nolink |}}  {{ :​wiki:​200px-nema_l520.png?​nolink |}} 
  
 <​bootnote critical>​Do not place electrical outlet directly behind the column</​bootnote>​ <​bootnote critical>​Do not place electrical outlet directly behind the column</​bootnote>​
-<​bootnote critical>​Be aware of voltage drop! Test the circuit to ensure that there is no greater than a 10% fluctuation in supply voltage while under load.</​bootnote>​+<​bootnote critical>​Be aware of voltage drop! Test the circuit to ensure that there is no greater than a 10% fluctuation in supply voltage while under load.  For circuits with irreparable and excessive voltage drop it is recommended to have a 220V circuit installed.</​bootnote>​
 <​bootnote critical>​Failure to operate the device on a dedicated circuit can result in failed x-rays, corrupt images, and damage to internal components.</​bootnote>​ <​bootnote critical>​Failure to operate the device on a dedicated circuit can result in failed x-rays, corrupt images, and damage to internal components.</​bootnote>​
 +\\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\ \\
 ---- ----
  
-<alert info>NETWORK & CONNECTIVITY REQUIREMENTS</​alert+<code>NETWORK & CONNECTIVITY REQUIREMENTS</​code
  
 [{{:​wiki:​direct_network.png|1. Direct Connection}}][{{:​wiki:​indirect_network.png|2. Indirect Connection}}] [{{:​wiki:​direct_network.png|1. Direct Connection}}][{{:​wiki:​indirect_network.png|2. Indirect Connection}}]
    
-  - Ordered List ItemDirect ​connectivity is where both the sensor (or flat panel) AND the core network connection of the machine are connected direct to the PC. +  - Direct ​connectivity is where both the sensor (or flat panel) AND the core network connection of the machine are connected direct to the PC. 
   - Indirect connectivity is where the core network connection of the machine is connected to the office'​s network and the sensor (or flat panel) is connected direct to the PC.   - Indirect connectivity is where the core network connection of the machine is connected to the office'​s network and the sensor (or flat panel) is connected direct to the PC.
  
Line 53: Line 45:
 <​bootnote critical>​Flat panel/​sensor connections must be connected with CAT6 cabling running at 1Gb. </​bootnote>​ <​bootnote critical>​Flat panel/​sensor connections must be connected with CAT6 cabling running at 1Gb. </​bootnote>​
 <​bootnote critical>​Do not place network jacks or exposure switch jack directly behind the column. </​bootnote>​ <​bootnote critical>​Do not place network jacks or exposure switch jack directly behind the column. </​bootnote>​
 +\\ \\
 ---- ----
  
-<alert info>​EXPOSURE SWITCH OPTIONS </alert+<code>​EXPOSURE SWITCH OPTIONS </code
-The exposure switch can be mounted next to the unit or it can be relocated anywhere within a 30-foot cable run. If the exposure switch needs to be relocated all that needs to be done is to have a CAT5 or CAT6 network drop run from where you want the exposure switch to be all the way to where the device is installed. ​Either end of the cable run will have an RJ45 jack.  +The exposure switch can be mounted next to the unit or it can be relocated anywhere within a 30-foot cable run. If the exposure switch needs to be relocated all that needs to be done is to have a CAT5 or CAT6 network drop run from where you want the exposure switch to be all the way to where the device is installed. ​Both ends of the cable run will have an RJ45 jack. \\ 
-[[File:GO_X5_exposure_switch_pinout.PNG|130px|Exposure Switch Wiring]] [[File:Relocated_exposure_switch.PNG|100px|Relocated exposure switch]] [[File:Local_exposure_switch.PNG|200px|Relocated exposure switch]]  +{{:wiki:​130px-go_x5_exposure_switch_pinout.png|}} 
 +{{:wiki:​100px-relocated_exposure_switch.png|}} 
 +{{:wiki:​200px-local_exposure_switch.png|}}
 ---- ----
  
-<alert info>SERVER REQUIREMENTS</​alert>+<code>SERVER REQUIREMENTS</​code>
 The imaging database should be installed on an existing file server. All that is needed is a shared directory with full read/​write/​execute permissions for all client PCs.  The imaging database should be installed on an existing file server. All that is needed is a shared directory with full read/​write/​execute permissions for all client PCs.